Plan and Elevation CADD [CBG]

General

Bridge: Since OpenBrIM supports the modeling of multiple bridges, this parameter should specify the bridge for which the Plan and Elevation drawing will be generated.

Start/End PGL #ft from Before/After Bridge [Use Alignment Start and End Station]: Users can either generate CADD according to the defined PGL boundaries (by setting to -1) or input a specific value to extend the CADD to a certain distance from the bridge start and end points.

Station Mark Every #nth Station: Specifies the interval at which station marks are placed on the drawing. This controls the spacing of station labels.

Number of Pieces btw. Station Marks: Defines the number of segments to divide the space between consecutive station marks, for finer level of detail representation.

Curve Refinement: Controls the smoothness of curved sections in the drawing by specifying the refinement level. Higher values produce smoother curves.

General Visual Setting

Dimension Line Font Size (Only .dgn): Sets the font size for dimension lines in .dgn format drawings.

Annotation Font Size: Specifies the size of annotation text on the drawing.

Annotation Arrow Size: Controls the size of arrows used in annotations.

North Arrow Station on PGL: Specifies the station location along the PGL where the north arrow should be placed.

North Arrow Transverse Offset from PGL: Sets the transverse offset distance for the north arrow, measured from the PGL.

Plan Visual Setting

Hide All Annotations and Dimension Lines [YES/NO]: Controls visibility of all annotations and dimension lines in the plan view [YES=1/NO=0].

BRG Out-to-Out Dim. Line Vert. Offset from Deck Edge: Sets the vertical offset distance for bridge out-to-out dimension lines, measured from the deck edge.

Span Length Dim. Line Vert. Offset from Deck Edge: Sets the vertical offset distance for span length dimension lines, measured from the deck edge.

Position of Span Dimension Lines [Left Side of The Bridge/Right Side of The Bridge]: Controls which side of the bridge the span dimension lines are positioned [Left side=1/Right side=2].

Display Pier Label [YES/NO]: Controls whether pier labels are displayed [YES=1/NO=0].

Position of Support Line Annotation [Left Side of The Support Line/Right Side of The Support Line/PGL Line]: Controls the position of support line annotations [Left side=0/Right side=1/PGL Line=2].

Support Line Annotation Vert. Offset from Point: Sets the vertical offset distance for support line annotations from the reference point.

Support Line Annotation Horz. Offset from Point: Sets the horizontal offset distance for support line annotations from the reference point.

PGL Name Box Vert. Offset from Point: Sets the vertical offset distance for the PGL name box from the reference point.

PGL Name Box Horz. Offset from Point: Sets the horizontal offset distance for the PGL name box from the reference point.

PGL Name Box Horz. Offset from Begin BRG: Sets the horizontal offset distance for the PGL name box from the beginning of the bridge.

Big Mark Length: Specifies the length of major station marks on the drawing.

Small Mark Length: Specifies the length of minor station marks between major marks.

Footing Dim. Line Offset: Sets the offset distance for footing dimension lines.

Extend Support Line to The Right Side: Extends the support line to the right by the specified distance.

Extend Support Line to The Left Side: Extends the support line to the left by the specified distance.

Display Bearing [YES/NO]: Controls whether bearings are displayed on the drawing [YES=1/NO=0].

Display Substructure [YES/NO]: Controls whether substructure elements are displayed on the drawing [YES=1/NO=0].

Display Supportline Across Deck Width [YES/NO]: Controls whether support lines are displayed across the full deck width [YES=1/NO=0].

Elevation Visual Setting

Hide All Annotations and Dimension Lines [YES/NO]: Controls visibility of all annotations and dimension lines in the elevation view [YES=1/NO=0].

Reference Line Elevation: Sets the elevation reference level for the drawing.

Piercap Slope: Specifies the slope of the pier cap in the elevation view.

Piercap Additional Vertical Offset: Applies an additional vertical offset to the pier cap in the drawing.

Show Only Right-Most Column [YES/NO]: If enabled, only the rightmost column is displayed [YES=1/NO=0].

Display Gap/Line at Girder End [Display Line/Display Gap/NO]: Controls how the girder end is displayed [Display Line=2/Display Gap=1/NO=0].

Ignore Skew at Pier [YES/NO]: If enabled, skew angles at piers are ignored in the drawing [YES=1/NO=0].

Display Gap btw Pier Cap-Girder [YES/NO]: Controls whether gaps between pier cap and girder are displayed [YES=1/NO=0].

Display Span Length [YES/NO]: Controls whether span lengths are displayed in the elevation view [YES=1/NO=0].

Show Ground Line from DTM [YES/NO]: If enabled, ground line from the Digital Terrain Model is displayed [YES=1/NO=0].

Trim Column from Ground Elev.: If enabled, columns are trimmed from the ground elevation level [YES=1/NO=0].

Display Abutment Slab Barrier [YES/NO]: Controls whether abutment slab barriers are displayed [YES=1/NO=0].

Trim Abutment Pile from Ground Elevation [YES/NO]: If enabled, abutment piles are trimmed from the ground elevation level [YES=1/NO=0].

Preferred DTM to Trim Columns: Specifies which Digital Terrain Model to use for trimming columns to ground elevation (when applicable).

Display Elevation of Substructure [YES/NO]: Controls whether substructure elevations are displayed [YES=1/NO=0].

Display Substructure Centerline [YES/NO]: Controls whether substructure centerlines are displayed [YES=1/NO=0].

Display Supportline Anno. Vertical [YES/NO]: Controls whether support line annotations are displayed vertically [YES=1/NO=0].

BRG Out-to-Out Dim. Line Vert. Offset from Align.: Sets the vertical offset distance for bridge out-to-out dimension lines, measured from the alignment.

Span Length Dim. Line Vert. Offset from Align.: Sets the vertical offset distance for span length dimension lines, measured from the alignment.

Support Line Annotation Vert. Offset from Align.: Sets the vertical offset distance for support line annotations, measured from the alignment.

Support Line Annotation Vert. Offset from Point: Sets the vertical offset distance for support line annotations from the reference point.

Support Line Annotation Horz. Offset from Point: Sets the horizontal offset distance for support line annotations from the reference point.

Substr. Annotation Vert. Offset from Point: Sets the vertical offset distance for substructure annotations from the reference point.

Substr. Annotation Horz. Offset from Point: Sets the horizontal offset distance for substructure annotations from the reference point.

PGL Name Box Horz. Offset from Begin BRG: Sets the horizontal offset distance for the PGL name box from the beginning of the bridge.

PGL Name Box Horz. Offset from Point: Sets the horizontal offset distance for the PGL name box from the reference point.

PGL Name Box Vert. Offset from Point: Sets the vertical offset distance for the PGL name box from the reference point.

PGL Start Annotation Box Horz. Offset from Alignment: Sets the horizontal offset distance for the PGL start annotation box from the alignment.

PGL Start Annotation Box Vert. Offset from Alignment: Sets the vertical offset distance for the PGL start annotation box from the alignment.

Roadway Plan Visual Setting

Display Traffic Lanes [YES/NO]: Controls whether traffic lanes are displayed in the plan view [YES=1/NO=0].

Display Lane Width [YES/NO]: Controls whether lane widths are displayed [YES=1/NO=0].

Display Superelevation [YES/NO]: Controls whether superelevation is displayed [YES=1/NO=0].

Display Traffic Arrows [YES/NO]: Controls whether traffic direction arrows are displayed [YES=1/NO=0].

Lane Direction (from right): Specifies the direction of traffic lanes relative to the right side of the roadway.

Roadway Annotation Loc. Dist. from Start of Roadway: Sets the distance from the start of the roadway where roadway annotations are placed.