> For the complete documentation index, see [llms.txt](https://docs.openbrim.org/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://docs.openbrim.org/templates/truss-bridge-workflow/superstructure-tb/truss-elements-tb/frame-member-tb.md).

# Frame Member \[TB]

A frame member is one continuous member through two or more Insertion Points, meshed into beam elements so that its bending can be read along its length. Use it for members whose moment diagram matters, such as a cross girder carrying concentrated loads between its supports, where a Truss would need many short pieces and many extra Insertion Points to show the same diagram. Between two consecutive Insertion Points the member is a straight line, also on a curved alignment, and it is always modeled with beam elements (axial, shear, bending and torsion stiffness).

The Insertion Points are the member's joints: at each of them the frame member connects to the other objects that use the same Insertion Point, such as Truss members, the same way a Truss does. The mesh nodes between the Insertion Points belong to the frame member alone and do not connect to anything else.

In the analysis results, the member has the two result lines (FE Composites) a girder has, a composite and a non-composite one, each along its whole length, so its forces and moments can be read from one end to the other; with no deck, the two give the same results. Where an offset moves the member past an Insertion Point along the member (at an end, or at every point with **Offsets At** = **All Points**), at the member's ends the line starts and ends at the Insertion Point's position along the member, so the part of the member beyond it has no result points, and at an interior Insertion Point it has a short stretch where its cuts take elements of both sides; read the element forces there. The line has a result point just each side of every interior Insertion Point. On a curved alignment, an Insertion Point that is placed relative to another station (for example with a longitudinal offset from its support line) shifts the result points next to it by a few inches, and the results on the elements next to it can differ from the element forces by one or two percent; read the element forces there. A result line cuts the member with planes square to it, so on a member with two spans 90° or more apart in direction (a portal, a column and its cap) a cut on one part also crosses the other part, and the line's values there are not the member's own; and one line has one set of axes, so on a member that mixes vertical and non-vertical spans the moments of some spans are about turned axes. Read the element forces there; the load ratings do not rate such members.

The frame member can be selected in **Truss Construction** and **Truss Deconstruction** like a Truss. It cannot be used by **Truss Load**, **Truss Load Rating (LRFR)**, **Truss Load Rating (LFD)** or **Gusset Plate**, which work with Truss members only. **Girder Load Rating (LFD)** and **Girder Load Rating (LRFR)** (as a non-composite member) can rate it: pick it as the Girder, and give the rating point as a span and a relative position on it (Location Input Method = *Relative on Span*). Its rating spans run between its ends and the Insertion Points that carry a bearing; with no bearing, the whole member is one rating span. These two ratings are the only objects that take a frame member as a girder: a deck, floor beam, lateral bracing, hanger or other object that takes a girder can be given one, but models it wrongly (a hanger, for example, connects to no node of it), so do not pick a frame member there.

## General

**Insertion Points:** Two or more Insertion Points the member passes through, in order. They are picked from previously defined Insertion Points; two consecutive points must not be at the same location, and the offsets must not move the two ends of the member between two points past each other (each gives a validation issue). The first and the last point are the member's ends; the points between them are its intermediate joints.

**Section:** Cross section of the member, used along its whole length when **Section Variation** is **Constant**. Use a section previously defined under **Properties > Sections** or import a new one. The section controls both the 3D view and the stiffness properties used by FEA.

**Section Variation \[Constant/Variable]:** **Constant** (the default) uses the **Section** above along the whole member. **Variable** takes the sections from **Section Data** instead, for a member whose depth or shape changes along its length, such as a floor beam whose ends taper into sidewalk brackets.

**Section Data:** The sections of a variable member, one row per point, shown when **Section Variation** is **Variable**. Each row gives the **Distance Along Member** from the first point, measured along the member line (so the member can run in any direction, as long as no two of its spans are 90° or more apart in direction), the **Section** there, and how the section changes up to the next row: **None** keeps the row's section up to the next row, where the next section starts; **Linear** and **Parabolic** (concave up or down) blend it into the next row's section. The distances run along the member line from the first point to the last one, before the Local Axial Offsets. Before the first row's distance the first row's section is used, and after the last row's distance the last row's, so a table usually starts at 0 and ends at the last point; the last row's variation is not used. At least two rows are needed, every row needs a Section, and the distances must increase from row to row. Every row's section must be made of the same shapes and points (for example the same built-up section with different plate sizes), because a varying section is blended shape by shape and point by point; a rolled shape cannot be blended into a section drawn from plates. The rows work as on a floor beam's section table.

**Variable Section Reference \[Centered/Top/Bottom/As Defined]:** How the sections of a variable member line up along it, shown when **Section Variation** is **Variable**. **Centered** keeps every section's mid-depth on the member line. **Top** lines up their tops on the member line, so a member that gets shallower keeps a flat top, and the offsets then place the member's top. **Bottom** lines up their bottoms, for a flat bottom, and the offsets then place the member's bottom. **As Defined** places every section by its own origin, for sections drawn to one common reference: for example a deep section centred on its origin and a shallower end section drawn with the same bottom, so the member line stays at the deep part's centroid and the end still has a flat bottom. The analysis places each section on the member line exactly as the reference draws it, so the section's offset from the line is taken into account: the reference changes where the member line, and the result line along it, runs, not the member's stiffness. With Top or Bottom the result moments are about that edge.

**Orientation Angle:** Rotation of the cross section about the member's longitudinal axis. Use this to orient asymmetric sections correctly relative to the member line.

**Vertical Offset (first point):** Vertical offset applied at the first point. Positive values shift the start of the member upward relative to its Insertion Point. The member is connected to the Insertion Point through a rigid offset.

**Vertical Offset (last point):** Vertical offset applied at the last point. Positive values shift the end of the member upward.

**Horizontal Offset (first point):** Transverse (horizontal) offset of the first point from its Insertion Point. Positive values shift the start of the member to the right when looking upstation.

**Horizontal Offset (last point):** Transverse (horizontal) offset of the last point from its Insertion Point. Positive values shift the end of the member to the right when looking upstation.

**Longitudinal Offset (first point):** Longitudinal (along-alignment) offset applied at the first point. Positive values move the start of the member upstation.

**Longitudinal Offset (last point):** Longitudinal (along-alignment) offset applied at the last point. Positive values move the end of the member upstation.

**Offsets At \[Ends Only/All Points]:** Where the vertical, horizontal and longitudinal offsets act. **All Points** (the default) applies them at every point: the first point takes the first point's offsets, the last point the last point's, and each intermediate point a value interpolated linearly between the two, in proportion to its distance along the member, so equal first and last values move the whole member by the same amount. Use it to place a member above or beside the joints it frames into, for example a stringer resting on floor beams: each Insertion Point is still the joint, and the member is connected to it through a rigid offset. Where the offset does not change linearly along the member, split it into several frame members. **Ends Only** applies the offsets at the first and the last point only, and the intermediate Insertion Points are used as they are, for example for an eccentric connection at one end of a member with several joints. With two Insertion Points the two settings are the same. The Local Axial Offsets act at the ends only in both cases.

**Local Axial Offset (first point):** Offset applied at the first point along the member's own axis; positive values move the start of the member inward, shortening it. Use for a rigid offset between the member's working point and the joint.

**Local Axial Offset (last point):** Offset applied at the last point along the member's own axis; positive values move the end of the member inward, shortening it.

## Mesh

**Max FE Element Length:** Longest beam element allowed in the FE model. Each span between two consecutive Insertion Points is divided into the fewest equal elements that are not longer than this value, up to 500 elements per span. Smaller values give a finer moment diagram and more nodes. The default is 24 in; the value must be at least 1 in, and at least the longest span's length after the Local Axial Offsets divided by 500 (a span takes at most 500 elements).

## Overrides

**Modulus of Elasticity Factor:** Multiplier applied to the section material's modulus of elasticity in FEA. Default 1.0 uses the unmodified material value; lower values soften the member.

**Poissons's Ratio Factor:** Multiplier applied to Poisson's ratio. Default 1.0.

**Section Area Factor:** Multiplier on the section area used by FEA. Default 1.0. Use to reduce the effective axial stiffness without changing geometry.

**Section Shear Area Y Factor:** Multiplier on the section shear area in the local Y direction. Default 1.0.

**Section Shear Area Z Factor:** Multiplier on the section shear area in the local Z direction. Default 1.0.

**Section Torsion Constant Factor:** Multiplier on the section torsion constant J. Default 1.0.

**Section Inertia Y Factor:** Multiplier on the section moment of inertia about local Y. Default 1.0.

**Section Inertia Z Factor:** Multiplier on the section moment of inertia about local Z. Default 1.0.

## EndRelease

The end releases act at the first and the last point only. The member is continuous through its intermediate Insertion Points.

**First Point Tx \[Free/Fixed]:** Translational end condition at the first point along the member's local X axis. **Fixed** transfers axial force; **Free** releases it.

**First Point Ty \[Free/Fixed]:** Translational end condition at the first point along local Y.

**First Point Tz \[Free/Fixed]:** Translational end condition at the first point along local Z.

**First Point Rx \[Free/Fixed]:** Rotational end condition at the first point about local X (torsion).

**First Point Ry \[Free/Fixed]:** Rotational end condition at the first point about local Y (bending).

**First Point Rz \[Free/Fixed]:** Rotational end condition at the first point about local Z (bending).

**Last Point Tx \[Free/Fixed]:** Translational end condition at the last point along local X.

**Last Point Ty \[Free/Fixed]:** Translational end condition at the last point along local Y.

**Last Point Tz \[Free/Fixed]:** Translational end condition at the last point along local Z.

**Last Point Rx \[Free/Fixed]:** Rotational end condition at the last point about local X.

**Last Point Ry \[Free/Fixed]:** Rotational end condition at the last point about local Y.

**Last Point Rz \[Free/Fixed]:** Rotational end condition at the last point about local Z.

**Use Local Release \[Yes/No]:** **Yes** applies the releases above in the member's local axes; **No** applies them in the global axes.

## Quantities

**Cross Section Area:** Area of the selected section; with a variable section, the area averaged over the member's length after the Local Axial Offsets, taken as varying linearly between the rows (exact when one dimension tapers). (Read-only)

**Length:** Length of the member between its ends, after the end offsets. (Read-only)

**Volume:** Cross section area times length. (Read-only)

**Weight:** Volume times the unit weight of the section material (with a variable section, the first row's section). (Read-only)

**Material:** Material of the selected section (with a variable section, the first row's section). (Read-only)

**Section:** Name of the selected section, or Variable for a variable section. (Read-only)

## IFC

**Type \[IfcBridge/IfcBridgePart/IfcBeam/IfcColumn/IfcSlab/IfcFooting/IfcPile/IfcBearing/IfcReinforcingBar/IfcReinforcingMesh/IfcTendon/IfcMechanicalFastener/IfcAlignment/IfcPositioningElement/IfcKerb/IfcGuardrail/IfcSurfaceFeature/IfcElementAssembly/IfcCableSegment/IfcSensor/IfcDistributionElement/IfcPlate/IfcWall/IfcRail/IfcRoad/IfcDiscreteAccessory/IfcDistributionSystem/IfcMember/IfcBuildingElementProxy]:** IFC entity class used on export. Default **IfcMember**, a structural member.

**Predefined Type \[Arch\_Segment/Brace/Chord/Collar/Member/Mullion/Plate/Post/Purlin/Rafter/Stay\_Cable/Stiffening\_Rib/Stringer/StructuralCable/Strut/Stud/Suspender/Suspension\_Cable/TieBar/UserDefined/NotDefined]:** Predefined-type attribute of the IFC entity. Default **MEMBER**; pick **CHORD**, **STRINGER** or another type that matches the member's role.

**Properties:** Custom IFC property entries attached to this member on export.


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://docs.openbrim.org/templates/truss-bridge-workflow/superstructure-tb/truss-elements-tb/frame-member-tb.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
